$30 DIY Sofa/Console Table Tutorial

I made it home safe from Seattle and it is right back to work! I mentioned earlier that I was staying with my cousin and helping her update her living room there. It was a pretty hectic week with both of us having to work and make a few last minute shopping trips in Seattle traffic, but we were able to accomplish a good amount and set aside time for some fun outings as well (more photos to come Friday!)

The project I am most proud of (and excited to share with you guys) is this sofa table I built:

I say proud because I figured out a way to build it using only a drill & screws (and a basic saw to cut a few small pieces of wood!) That means 95% of you can do this too. By yourself. In one day, for $30 or less.

Materials

• 2x2x8' furring strips(qty 8)
• 2x12x10' (qty 1)
• Screws(2.5-3″ long)
• Wood glue
• Wood stain or paint

Tools

• Drill
• Saw (miter, chop saw or miter box)
• Kreg Jig(or unfussy brackets)
• Sand paper(or electric sander)

My cousin had a long sofa (just over 9 feet wide) and was using an end table that was blocking part of the walkway, so I thought the well suited solution would be a long narrow table behind the sofa for more convenient storage.

I was having trouble finding a unfussy plan I liked online, and knew this table definitely had to be customized so The choice was to come up with my own. We were also working with a budget so The aim was to do this as inexpensively as possible.

I drew a quick sketch to illustrate my idea (excuse the roughness of it):

I was envisioning a very unfussy, modern style table constructed using 2×2's and a 2×12″ for the top portion. The drawing is not particularly accurate as there should be 2×2's horizontally at the top for reinforcement (below the 2×12) but you get the idea. I knew 2x2x8' furring stripswere under $2 each and the 2x12x10' was only around $12, making this project about as cheap as you can get for such a large table.

This can be done a lot simpler and for even less if you plan on making a shorter table by eliminating the middle piece. I put it in there for stability, but if the table was shorter than ~6 feet or so, I would leave it out.

Here is what we brought back from the hardware store—a 2x12x10' and eight 2x2x8's. Unfussy stuff.

My cousin had very limited, basic tools in her garage which proved to be a challenge but fortunately we were able to borrow a neighbor's saw to make the smaller cuts, and we had the the 2×12 cut to 9' for us.

You will end up with three different sizes—the long horizontal pieces, the vertical legs, and the shorter pieces to connect the legs (these will be different depending on the size of your table).

First it is time to assemble the rectangles! I grabbed four pieces and arranged them:

You will need to drill pilot holes so the wood does not split—that is a very important step especially with this type of wood that splinters easily and since the pieces are so narrow. I was able to find 3 drill bits in the garage and luckily one of them ended up working. You want it to be just a bit smaller than the width your screw.

I bought 2.5″ screws for this project which worked fine but 3″ may have been even better. First I aligned my two pieces into place and drilled my pilot hole through both. I made sure to do this towards one end of the board instead of the center, since I would have to insert another screw in the same area for the horizontal pieces and there needed to be enough room for both screws to pass through without hitting each other.

Then I applied the glue onto the end of a short piece…

After setting it back into position, the first screw went in:

I did this on each end (3 more times) until my rectangle was built:

And then built the remaining two pieces. Step 1 complete!

This is where it gets a little trickier when you are working by yourself. You have to start balancing things and holding them into position while attaching them together with glue and screws. I had no clamps or flat surface to work on, and the drill I was using did not have plenty of power, and the drill bits did not fit the screw heads perfectly so there was some frustration involved. If I can do it under these conditions, you definitely can too!

The next step is to attach the long horizontal pieces. I propped up my rectangle and got the pieces into place, then repeated the attachment process with my pilot hole, wood glue and screw. It seemed to work fine…

But when I lifted it up to flip it over and add the other two horizontal pieces, I found they were wobbly so I had to reinforce it with a second screw. One screw works fine for the smaller lengths of wood but just does not cut it for the longer pieces. And I made sure to counter sink them so that a) they'd grab a little more of the wood and b) I could fill the holes so there were not any visible screws.

Two screws did the trick, and I then attached the second rectangle to the opposite end.

I flipped that piece over and attached the last two horizontal pieces the same way. If you were building a smaller table, this would be your last step before adding the top and it would be pretty much the easiest project ever.

But I had the dilemma of attaching a whole other section without a Kreg Jig or anything of the sort, so I ended up buying 2″ brackets:

This part was definitely the biggest challenge of the entire project. Even with two screws holding the longer pieces together, they are quite long so they do not stay perfectly straight and I had to hold everything into place while keeping them elevated and drilling pilot holes, applying glue, lining up the brackets and attaching the screws.

Somehow I made it all happen. Precise measurements and cutting is a crucial step, otherwise everything may not all fit together!

Also, these furring strips are not well suited, but luckily dark stain goes a looong way to hide imperfections. I did not even have wood filler so I used drywall mud + sawdust and you cannot tell at all with the finished product.

After the brackets went on and the base of the table was finished, it was a huge relief!

The next part was easy—add some wood glue to the top:

Then lift your 2×12″ into place.

And secure it with screws from underneath. I used 8 in total.

Then it was all about the finishing touches. There was no electric sander available so I picked up some 80 grit and went over each piece by hand. Labor of love, baby.

After it was all smooth and splinter-free, I applied a dark walnut stain which coordinates nicely with the warm woods in her home.

Finally, I brushed a shellac onto the top piece (for extra durability) and used a matte wax on the base since it is easier/faster and that part does not need the same level of protection as the top.

We hauled it upstairs to the living room and set it in place. And it is well suited.

Her home is a split level so it is one of the first things you see when you walk upstairs into the living room:

The back wall hides half of it, but it is such a versatile piece that can be moved anywhere and travel to new homes in the future.

And they get a fun area to display pretty things.

I am just a little bit jealous and know exactly what I'll be making for myself the next time I need a table!

Now I am passing on the challenge to you—if you have a way to cut wood and a drill, you can make it too!

This has to be one of my top 3 furniture builds ever and it was so rewarding to see how much my cousin loved it and how happy she is to have it in her home. And I hope this will inspire you to take action as well and try something new!

Hope you are all enjoying the first official week of summer—make sure to keep up with everything that is been going on over on instagram and I'll be back Friday with more photos.

If you like this project, look at these popular beginner budget DIYs from my Project Library!

1. $10 canvas floating frame
2. How to realistically age wood (the easy way!)
3. Easy string light planters
4. Board + Batten tutorial