New Laundry Room: DIY Barn Door

SaSo far this renovation has been one of our easiest—of course much of that can be attributed to the fact that we have hired out plenty of the hard labor, but now that we are in the DIY phase, it was only a matter of time before we ran into a few bumps.

Let me be honest and real for a minute. We are far from DIY professionals—in fact, more than half the time we are trying something we have never attempted before and have no idea what we are doing. The hope with this blog is to share our experience and encourage those of you who are also unsure of their abilities to get out there and do it—or, learn from our mistakes and do things a different way or hire it out (no shame in that!)

When I started blogging 4 years ago we had nothing more than a crappy battery powered drill and some screwdrivers. We often found ourselves in DIY hell, on the verge of quitting so many times. I have finally learned that the key is having the right tools, and time/experience. With experience also comes knowing when a job is too big/technical/time consuming and it is worth hiring out. Honestly if we could afford to hire everything out, we probably would. We do not DIY for fun but there is definitely the reward of personal accomplishment that comes along with it (and every now and then a project is actually enjoyable!)

Moral of the story is… I can share our journey in a handful of words and photos and make it all look quick and easy, but there is a lot that goes on behind the scenes. And sometimes it genuinely sucks. I do not want to lead anyone to believe that they can take on more than they can handle and end up with a nightmare project (been there too many times). I aim to be as thorough and honest as possible so you can make those decisions yourself based on your skill level/resources. And please, learn from our mistakes, because we make them all the time.

Back to our latest project.

As you may recall, we built this wall and doorway into the storage room:

Technically it does not need a door…. but I have been obsessing over barn doors for years and this was the well suited opportunity to finally try it out. Brad was fully on board as well so when I came across someone taking apart an old barn down the street, I offered to take some boards off his hands. $20 later and it was all mine:

After measuring the door opening and deciding on a door size, I started laying out a few ideas for a door design and came up with this:

The vertical boards were too short to span the full height (around 75″) so I had to place a horizontal board on the top and bottom and extend them out a little to add some height.

First I lined up my vertical boards and trimmed the ragged ends off:

Much better.

Then I grabbed my two horizontal peices and trimmed them to the door width (31″).

To attach the boards, I flipped everything over to hide the screws, and lined it all back up (apparently I missed an important step here which you will see in a moment…)

Once I had everything lined up and triple checked my measurements to make sure everything was square, we drove two screws into the ends of each board.

For the cross piece, we set it on top of the door in the position we wanted and marked a cut line.

I used a skill saw to cut the edges. A well suited fit!

With the door raised on sawhorses, Brad was able to get underneath with the drill and screw the cross peice in from the back while I applied pressure from the top.

And we had our door!

This is where the easy/fun part ended.

Back inside the room, we unpackaged the hardware kit (which we purchased on Ebay for $90 shipped):

The graphics-only installation guide was not terribly clear and there were a few parts that we still have no idea what their purpose is, but overall it seemed pretty easy and straightforward.

But then as soon as we held the door hanger up we realized we had a major issue…

There was nowhere for the rail to attach to, since the wall did not come down far enough (it is a standard door opening height but the top ran into a ceiling beam so there was not enough flat wall space). After a brief moment of panic and despair, we decided the only solution was to secure a 1×6″ across the top of the wall and attach the rail to that. Brad thought it was going to look ridiculous but I did not care—nothing was going to stop me from my barn door dream!

I promptly ran to Lowe's to grab the board and once it was hung, we were both relieved when it did not look as awkward as we had anticipated (of course it still needed some trim and spackle & caulk to blend in):

Then it was time to mount the rail which presented another problem—the screws they come with are designed to go into a wall, but that would not work where the 1×6″ was hanging in the doorway since there was nothing on the other side of it. So I had to pick up some bolts, nuts and washers at Lowe's. Here you can see the screws we used for the wall side in black, and the bolts on the right:

The rail mounts onto spacers so the hanger can slide freely without hitting the wall. We had to make sure each bolt it was 100% perfectly level as we went or else the door would slide on its own:

We made sure to predrill our holes before inserting the screws so the wood would not split. Here is the mounted rail:

A quick double check to make sure there was enough room to lift the door on…

Back to the door. After measuring and deciding where The aim was to mount the hangers, we drilled a couple holes for the bolts to pass through.

Then we discovered yet another problem:

The bolts were too long! Not only that, but the lower bolt would need to pass through two layers of wood and it was too short for that:

So it was back to Lowe's again. Brad picked up two different sizes along with a couple washers and nuts to secure them.

This is how it looks from the back:

And finally that part was over…

Now all we had to do was lift it onto the track and hope for the best….!

You guys, it was so crooked.

I am not sure why it does not genuinely come through in the photo but it was so, so off. We could not figure out where we had gone wrong. All we could do was remove the left hanger hardware, drill new holes and reattach it. That straightened it out but we were left with this uneven gap at the top…

We decided that the top and bottom pieces hadn't been attached completely square with the vertical pieces, and I am genuinely not even sure how we could have avoided it. I measured very carefully but things shift and none of this wood is particularly straight or even, so… it happened. But it is a rustic door, and I am trying to embrace it, so I am just going to pretend that our door just has its own style and wants to be that way. Door swagger.

We still were not done, however. The door slid nice and smoothly across the rail but there was nothing touching the ground to guide it and it could easily be pushed back and forth, hitting the wall, and also because it was not 100% level it wanted to slide shut on its own. Who knew barn doors could be so complicated?

The rail kit came with this plastic guide in which it seems you are supposed to screw into your floor and route a groove for it to slide through in the bottom of your door.

I am not sure why they would think that the average person has access to a router and/or hardwood floors to drill into, but we had neither of those.

Fortunately, we did find these wheels in the garage and decided to give them a shot.

We attached them to the back of the door and they worked like a charm!

You can still pull and push on the door if you genuinely wanted to, but it stays straight just opening and closing it. And I cannot genuinely think of a reason we will ever need/want that door to be closed.

For the finishing touches I added quarter round to the top of our 1×6 and spackled, caulked and painted (there is a gap on the right for door trim which we will add very soon):

I also touched up all the silver bolts with black acrylic paint, and picked up this utility handle from Lowe's and spray painted it black.

And that is the story of our perfectly imperfect rustic DIY real barn door.

It helps to keep this barn wood so much. I want some in every room now.

There will definitely be more of these in our future (home theater room, I am looking at you…)

We just have to figure out how to build a perfectly straight door first. But for now, I am definitely loving the latest addition in here and the fact that it did not break the bank (and I still have barn wood leftover!). If you are wondering, yes I would absolutely buy the same door hardware again. It is the cheapest one I found on ebay, you can adapt it to fit your door size and we have no complaints.

Next up on the agenda is relocating the washer & dryer and building a couple storage drawers. If all goes well, this alcove will be completely functional by this time next week!

We are not building the drawers until this weekend, so I'll most likely wait until Monday to post everything. In the meantime, you can find me over on instagram for more frequent updates.

Here is to a happy and productive week!